It is one of the most common questions we get: you have a bag of polymeric sand left over from the patio and a cracked concrete driveway, so can you use the sand to fill concrete cracks? The short answer is no. Polymeric sand is made for the joints between pavers, not for cracks in a concrete slab, and no manufacturer we carry rates it for that job.
This guide explains why, what to use instead for each kind of crack, and how to pick the right product for your driveway, sidewalk or patio.
Quick answer
- Polymeric sand is not made for concrete cracks. Manufacturers rate it for paver and stone joints with a minimum depth, and they publish those rules on the bag.
- For hairline cracks and cracks up to 2 in wide, use a crack filler made for concrete, such as ConSandtrate, which pours in dry and sets when misted.
- For expansion and control joints that move, use a flexible sealant rated for movement, such as Sikaflex + Self Leveling or Sashco Slab.
- For large voids or a worn slab, use a cementitious patch or resurfacer.
In this guide
Why polymeric sand does not belong in concrete cracks
Polymeric sand works because of how a paver joint is built. The pavers sit on a compacted base and bedding layer, the joint is deep, and the sand locks the pavers together once it is watered in. The manufacturers set rules around that:

- Minimum joint depth. Alliance lists a minimum joint depth of 1-1/2 in for Gator Maxx G2 and Super Sand G2, and SRW lists the same for Pavermate Z3. A typical driveway crack is nowhere near that deep and uniform.
- Joint width ranges. Each sand is rated for joints within a set range, such as 1/8 in to 2 in. Concrete cracks taper from hairline to wide within a few feet.
- Surfaces. Product pages list pavers, natural stone and, for some products, porcelain. None list cracks in a concrete slab.
Pack polymeric sand into a shallow crack in a slab and it has little depth to bind, no pavers to lock, and a slab moving around it with every freeze and thaw. It tends to break up and wash out.
What to use instead
The right product depends on the crack. Here is how the concrete repair products we carry line up:
| Crack or joint | Use | Key limits from the manufacturer |
|---|---|---|
| Hairline cracks and cracks up to 2 in wide in driveways, walks, patios and pool decks | ConSandtrate Concrete Crack Filler | 3 lb bottle covers about 12 to 15 linear ft; backfill cracks wider than 1 in with pea gravel or similar aggregate first |
| Cracks and joints up to 3 in that move | Sashco Slab | Textured acrylic, backer rod in joints deeper than 1/2 in |
| Horizontal expansion and control joints, 1/4 in to 1-1/2 in wide | Sikaflex + Self Leveling Sealant | Plus or minus 25 percent movement, 2 to 1 width to depth ratio, backer rod always |
| Small cracks up to 1/2 in, including masonry | Liquid Nails CR-805 | Joints over 1/2 in are listed as not recommended |
How ConSandtrate works (and why people confuse it with polymeric sand)
ConSandtrate looks and pours like sand, which is where the mix up comes from. It is a dry granular polymer crack filler made for concrete, not a paver joint sand. You pour it into a clean, dry crack, mist it, and it sets into a hardened, self healing infill with a sandy, grout like texture. It comes in Gray, Tan, Brown, White and Black.
- Clean the crack of loose debris, old filler and dirt.
- Let it dry completely. A damp crack activates the polymer too early.
- Backfill with pea gravel or similar aggregate first if the crack is wider than 1 in.
- Pour ConSandtrate to the surface.
- Mist lightly with a spray bottle. Do not flood it.
- Top up and mist again if it settles, then keep the area dry while it cures.
The maker states it is dry to the touch and can handle traffic after about 1 hour, with full cure taking 48 hours. Our full ConSandtrate guide covers coverage by pack size.
Common mistakes with concrete cracks
- Using a rigid patch on a moving crack. Cement patches are rigid, so the next freeze and thaw usually cracks them along the same line.
- Skipping backer rod. On deep cracks and joints, backer rod saves product and gives sealants the right shape.
- Filling a wet crack. Water trapped under the repair keeps doing damage.
- Putting paver sand in a slab. Save it for paver joints, where it works.
When polymeric sand is the right answer
If the "cracks" are actually the joints between pavers or stone, polymeric sand is exactly the right product. Read how to fix cracked polymeric sand joints or our guide to the best polymeric sand for your pavers.
Frequently asked questions
Can I use polymeric sand in driveway cracks?
No. Polymeric sand is rated for paver and stone joints with a minimum depth, not for cracks in a concrete slab. Use a concrete crack filler such as ConSandtrate, or a flexible sealant for joints that move.
What is the best filler for hairline cracks in concrete?
For hairline cracks and cracks up to 2 in wide in driveways, walks, patios and pool decks, ConSandtrate pours in dry and sets when misted. A 3 lb bottle covers about 12 to 15 linear feet.
What should I use on a concrete expansion joint?
A flexible sealant rated for movement. Sikaflex + Self Leveling Sealant handles horizontal joints from 1/4 in to 1-1/2 in wide, and Sashco Slab goes up to 3 in. Use backer rod as each manufacturer directs.
Why does cement patch keep cracking?
Cement patches are rigid. The next freeze and thaw usually cracks them again along the same line, which is why flexible fillers and sealants are used on moving cracks.
Have a crack to fix? ConSandtrate comes in five colors, and our concrete repair collection has sealants for joints that move. Send a photo with a tape measure through the contact page or call (856) 418-4895.
Related guides: ConSandtrate Concrete Crack Filler: How to Apply It and Coverage, How to Fix Cracked Polymeric Sand Joints That Last, Best Polymeric Sand for Pavers: Picks by Joint Width, Stone and Weather