Techniseal Structure Bond Gun Cleaner for Foam Adhesive Dispensers
The Difference Between A Dispenser That Lasts A Season And One You Throw Away
Polyurethane foam adhesive cures inside a dispenser and turns it into a paperweight. This cleaner dissolves uncured Structure Bond residue rapidly, and it is built to fit the Structure Bond Gun II dispenser directly. It also removes foam adhesive spillage from any solvent resistant material, which is the other problem foam adhesive creates on a job site.
|
Fits Gun II Directly Designed for Structure Bond dispensers |
Dissolves Uncured Residue Rapid cleaning between applications |
|
Removes Spillage From solvent resistant materials |
Saves The Gun Cured foam inside is permanent |
Why Contractors Ask for Structure Bond Gun Cleaner by Name
A Structure Bond dispenser is a real tool with a real cost. Leaving foam adhesive to cure inside it is how crews replace them every few months instead of every few years.
- It rapidly dissolves uncured adhesive residue. Clean the gun between applications and it keeps working properly rather than gumming up and delivering an inconsistent bead.
- It fits the Gun II dispenser directly. Cleaning becomes a two minute job at the end of the day rather than a disassembly.
- It removes foam adhesive spillage from any solvent resistant material, which is genuinely useful when foam lands somewhere it should not.
- It tackles dry foam accumulation, not only fresh residue, so a gun that has been neglected is often recoverable.
- It protects the delivery accuracy that made you buy a canister system in the first place. A partially blocked gun wastes expensive adhesive on every trigger pull.
Structure Bond Gun Cleaner Specifications
| Product Type | Dispenser cleaner for foam adhesive |
| Designed For | Techniseal Structure Bond Gun II dispensers |
| Dissolves | Uncured Structure Bond adhesive residue and dry foam accumulation |
| Also Removes | Foam adhesive spillage from solvent resistant materials |
| Coverage | Apply as needed |
| Manufacturer | Techniseal |
Usage depends on how often you clean, which should be after every use. A container lasts a long time in normal use because each cleaning cycle uses very little.
Where Structure Bond Gun Cleaner Works
Anywhere Structure Bond is being used.
- Cleaning the Gun II dispenser between applications
- End of day gun maintenance on a multi day wall build
- Recovering a dispenser with dry foam accumulation
- Removing foam adhesive spillage from tools and solvent resistant surfaces
- Retaining wall, column, and cap stone construction sites
- Any crew running Structure Bond canisters regularly
Where Structure Bond Gun Cleaner Should NOT Be Used (Straight From the Manufacturer)
It removes uncured adhesive. Fully cured polyurethane foam is far harder to shift, so clean promptly rather than hoping this fixes a long neglected gun.
Only use it on solvent resistant materials. Techniseal is specific about that. Test before using it near finished stone, plastics, or coated surfaces.
It is a maintenance product, not an adhesive remover for finished work. For cured foam on a paver face, check the technical data sheet first.
Read the technical data sheet and safety data sheet before use, including ventilation and protective equipment.
Not sure if your project qualifies? Call or text us at (856) 418-4895 before you order. We will give you a straight answer, even if the answer is that this is not the right product for your job.
How to Use Structure Bond Gun Cleaner
Follow the official Techniseal instructions, linked below. This is the shape of the job:
- Finish your adhesive application and remove the Structure Bond canister from the gun.
- Thread the cleaner onto the Gun II dispenser in place of the canister.
- Run cleaner through the gun per the technical data sheet until the residue is dissolved and the delivery runs clear.
- Wipe down the exterior and the nozzle area.
- For spillage, confirm the material is solvent resistant, then apply and remove per the instructions.
- Store the gun clean and ready for the next canister.
Clean the gun the same day, every day. Foam adhesive cures on its own schedule and a dispenser left overnight uncleaned is usually a dispenser you replace.
Quick Answers
Will it save a gun that already has cured foam in it?
It is formulated to dissolve uncured residue and dry foam accumulation. Heavily cured foam may be beyond recovery, so clean promptly.
Does it fit my dispenser?
It is specifically designed to fit Structure Bond Gun II dispensers.
Can I use it to clean adhesive off pavers?
Only on solvent resistant materials, and test first. Check the technical data sheet before using it near finished surfaces.
How often should I clean the gun?
After every use. That is the single habit that determines how long a dispenser lasts.
Is it necessary?
If you use Structure Bond regularly, yes. The cleaner costs a fraction of a replacement dispenser.
Official Techniseal Documentation
Documents are published by Techniseal and open in a new tab. Every sheet we carry is also listed in our TDS and SDS library.
Pairs Well With
- Techniseal Structure Bond adhesive canister
- Techniseal Structure Bond Gun II dispenser
- Techniseal Structure Bond PU Paste for gap filling and shimming
Order before our daily cutoff and your Structure Bond Gun Cleaner ships today from New Jersey.
Questions about your project? Call or text (856) 418-4895 and you will get a real person who works with hardscape adhesives and tools every day.
Not sure how many 50 LB bags of polymeric sand your paver project will need? Try our Polymeric Sand Calculator
