Alliance Designer Products · Sold by Polymeric Sand Store
Gator Hybrid Seal Low Gloss Water Based Sealer for Pavers and Stone
Low gloss water based sealer for concrete pavers. No color enhancement. Can be applied on damp surfaces. Penetrates deep to protect against oil, de icing salt, and UV damage. Low gloss finish with no color enhancement. Works down to 40°F. Can be applied on damp surfaces. Rain safe in 24 hours.
Low Gloss. No Color Enhancement.Works Down to 40°FCan Apply on Damp Surfaces
200 ft²/galCoverage per gallon
24 hoursRain safe after
1 gal / 5 galAvailable sizes
What Is Alliance Alliance Gator Hybrid Seal Low Gloss Water Based Paver Sealer?
Important: Alliance Gator Hybrid Seal Low Gloss is for unsealed concrete paver surfaces only. It cannot be used as a resealer over an existing sealer coating. Pavers must be clean and largely dry, though Alliance Gator Hybrid Seal Low Gloss can be applied on slightly damp surfaces unlike solvent based sealers and free of all stains and efflorescence before application. Wait at least 60 days after new paver installation before sealing. Temperature must be between 60°F and 85°F at time of application.
Alliance Gator Hybrid Seal Low Gloss is an water based acrylic sealer that penetrates deep into concrete paver surfaces to protect them from the inside out. It delivers a high gloss wet look finish that enhances the natural color of your pavers with a subtle sheen. The result is a clean low gloss appearance that makes pavers look their best while adding a durable protective layer underneath.
Alliance Gator Hybrid Seal Low Gloss protects concrete pavers against oil and dirt penetration, de icing salt corrosion, and UV ray damage that fades paver color over time. It also acts as a joint stabilizer, helping to firm up polymeric sand joints and reduce joint erosion between sealing cycles. One coat is all that is needed. When used as a joint sand stabilizer with ASTM C144 sand rather than polymeric sand, coverage is approximately 100 sq ft per gallon. Alliance Gator Hybrid Seal Low Gloss is rain safe just 24 hoursutes after application and the sealed surface can be used after 24 hours.
Available in 1 gallon and 5 gallon sizes. Coverage is approximately 200 sq ft per gallon as a stand alone sealer, meaning the 5 gallon size covers approximately 1,000 sq ft as a stand alone sealer. suitable for most residential driveways and large patio areas. Two people are recommended for application. Apply with a sprayer in 60 sq ft sections and back roll with a water based foam roller (yellow) to remove excess sealer from the surface.
Not sure which sealer is right for your pavers? We sell an 8 oz sample bottle of this sealer so you can test the finish and appearance on your specific pavers before committing to a full 1 gallon or 5 gallon order. Order a sample here.
Not sure whether Alliance Gator Hybrid Seal Low Gloss is the right finish for your pavers, or whether you need Satin Look, Natural Look, or Resealer instead? Call or text us 24/7 at (856) 418-4895 and we will help you choose the right sealer before you order.
1 Gallon
Covers approx. 175 sq ft
5 Gallon
Covers approx. 875 sq ft
Is Alliance Gator Hybrid Seal Low Gloss the Right Sealer for Your Pavers?
Unsealed surfaces only. Not a resealer. Alliance Gator Hybrid Seal Low Gloss is formulated for first time sealing of bare unsealed concrete pavers. If your pavers are already sealed, you need Gator Seal Resealer instead. Not sure if your pavers are sealed or unsealed? Call us at (856) 418-4895.
Homeowners who want a clean finished look without heavy gloss Alliance Gator Hybrid Seal Low Gloss delivers a high gloss wet look finish that enhances paver color and gives the surface a well-maintained polished appearance without the mirror-like shine of a wet look sealer. It is the finish of choice for homeowners who want the maximum visual impact and the most vibrant, color-enhanced appearance from their paver surface.
Concrete paver driveways, patios, walkways, and pool surrounds Alliance Gator Hybrid Seal Low Gloss is suitable for all standard concrete paver applications including driveways, patios, walkways, steps, and pool surrounds. The sealer protects against the specific challenges each surface faces: oil from vehicles on driveways, de icing salt in colder climates, and UV fading on sun-exposed surfaces.
Paver surfaces with polymeric sand joints that need stabilizing Alliance Gator Hybrid Seal Low Gloss acts as a joint stabilizer in addition to sealing the paver surface. This dual function makes it particularly valuable on paver surfaces where the polymeric sand joints are beginning to show wear or where extra joint stability is wanted between re-sanding cycles.
Cold climate applications where de icing salts are used Alliance Gator Hybrid Seal Low Gloss creates a protective barrier inside the paver that resists corrosion from de icing salts. This makes it particularly well suited for driveways and walkways in northern climates where salt and calcium chloride are applied in winter.
Not for already sealed pavers or natural stone Alliance Gator Hybrid Seal Low Gloss is formulated for bare unsealed concrete pavers only. It cannot be used over an existing sealer coating. use Gator Seal Resealer for that application. It is not recommended for natural stone surfaces.
Comparing sealer finishes? Wet Look sits between Natural Look (no sheen) and Wet Look (high gloss). If you want the pavers to look exactly as they do naturally, choose Natural Look. If you want a bold wet appearance, choose Wet Look. Satin is the balanced option most homeowners prefer. Still unsure? Call or text us at (856) 418-4895.
What Does Alliance Alliance Gator Hybrid Seal Low Gloss Water Based Paver Sealer Do?
High gloss wet look finish with enhanced color Alliance Gator Hybrid Seal Low Gloss delivers a refined high gloss finish that enhances the natural color of concrete pavers with a subtle high gloss wet finish. The finish makes pavers look cleaner and more vibrant without the heavy reflective gloss of a wet look sealer.
Deep penetrating acrylic formula Alliance Gator Hybrid Seal Low Gloss penetrates deep into the concrete paver structure rather than forming a thick film on the surface. This deep penetration ensures the protective properties work from within the paver, creating a more durable and longer lasting seal compared to surface-only coatings.
Protects against oil, dirt, de icing salt, and UV damage Alliance Gator Hybrid Seal Low Gloss creates a barrier inside the paver that resists oil and dirt penetration, de icing salt corrosion, and UV ray damage that causes paver fading and color degradation over time. Sealed pavers are significantly easier to clean and maintain.
Acts as a joint stabilizer In addition to sealing the paver surface, Alliance Gator Hybrid Seal Low Gloss penetrates into the polymeric sand joints and helps stabilize them, reducing joint erosion and extending the life of the jointing material between re-sanding cycles.
Rain safe in 24 hoursutes Alliance Gator Hybrid Seal Low Gloss is water repellent and rain safe just 24 hoursutes after application. Once rain safe, light rain will not damage the applied sealer. The sealed surface is ready for foot traffic and normal use after 24 hours.
One coat application Alliance Gator Hybrid Seal Low Gloss requires only one coat. Applying a second coat is not recommended and will not improve results. The spray and back roll application method ensures even coverage and removes excess sealer that could cause uneven appearance or pooling on the surface.
How to Apply Alliance Alliance Gator Hybrid Seal Low Gloss Water Based Paver Sealer
Critical pre-application requirements: Pavers must be at least 60 days old. Surface must be 100 percent dry. pavers and jointing sand both. Temperature must be between 40°F and 85°F. Paver surface must be cool to the touch. No rain expected within 24 hours of application. Allow 48 hours after polymeric sand installation before sealing. All stains, efflorescence, and existing sealer must be fully removed before Alliance Gator Hybrid Seal Low Gloss is applied. Test on a hidden 4 sq ft area first.
1
Remove all stains and strip any existing sealer
Remove all oil, grease, and rust stains using the appropriate Gator Clean products. If any unknown coating exists on the paver surface, remove it completely using Gator Sealer Stripper before applying Alliance Gator Hybrid Seal Low Gloss. Applying over a contaminated or previously sealed surface will result in poor adhesion and sealer failure.
2
Replace contaminated jointing sand
Remove all contaminated jointing material and replace with fresh Gator Polymeric Sand following the standard installation instructions. Allow the new polymeric sand to harden for a minimum of 48 hours at above 60°F with no rain before proceeding to the next step.
3
Clean the entire surface with Gator Efflorescence Cleaner
Clean the entire paver surface with Gator Efflorescence Cleaner. This removes any efflorescence trapped in the paver pores and thoroughly cleans the surface to ensure proper sealer adhesion. Wait at least 48 hours at above 60°F with no rain after cleaning so the surface and polymeric sand are completely dry before applying Alliance Gator Hybrid Seal Low Gloss.
4
Apply Alliance Gator Hybrid Seal Low Gloss in 60 sq ft sections
Using a sprayer, apply one coat of Alliance Gator Hybrid Seal Low Gloss in sections of approximately 60 sq ft at a time. Do not thin or dilute the product. Apply evenly across each section before moving to the back rolling step. Work in sections to ensure the sealer does not begin to cure before the roller step is completed.
5
Back roll immediately with a water based foam roller (yellow)
Immediately after spraying each 60 sq ft section, use a water based foam roller (yellow) to back roll the Alliance Gator Hybrid Seal Low Gloss, removing excess sealer left on the surface. This step is critical to achieving an even, consistent finish. This is why two people are recommended. one sprays while the other back rolls. Apply one coat only.
6
Allow 24 hoursutes to rain safe, 24 hours to full use
Alliance Gator Hybrid Seal Low Gloss is rain safe 24 hoursutes after application. Keep foot traffic and vehicles off the sealed surface for 24 hours after application to allow the sealer to fully cure. Clean all application equipment with water and soap immediately after use.
Do not apply Alliance Gator Hybrid Seal Low Gloss if any of these conditions exist
Pavers are less than 60 days old
Surface is damp or wet. pavers and sand must be 100 percent dry
Temperature is below 60°F or above 85°F
Rain is forecast within 24 hoursutes of application
48 hours of dry conditions before application have not been confirmed
Existing sealer coating has not been fully stripped
Stains, efflorescence, or contamination remain on the paver surface
Technical Specifications: Alliance Alliance Gator Hybrid Seal Low Gloss Water Based Paver Sealer
Product typeWater based acrylic paver sealer
FinishHigh gloss wet look
Compatible surfacesUnsealed concrete pavers only
Can be used as resealerNo. unsealed surfaces only
Coverage per gallonApproximately 175 sq ft (varies by porosity and joint size)
Coverage per 5 gallonApproximately 875 sq ft
Number of coatsOne coat only
Application methodSprayer and water based foam roller (yellow). 2 people recommended.
Section size per application pass60 sq ft sections
Rain safe after application24 hoursutes
Full use after application24 hours
Application temperature40°F to 85°F (16°C to 29°C)
Dry conditions required before applyingMinimum 48 hours
Minimum paver age before sealing60 days after installation
Joint stabilizerYes
Tool cleanupWater and soap
Dilution requiredNo. apply full strength
Minimum storage temperatureAbove 32°F (0°C) at all times
Available sizes1 gallon and 5 gallon
ManufacturerAlliance Designer Products Inc.
All specifications sourced from the official Alliance Gator Technical Data Sheet (TDS). Always verify the latest TDS at AllianceGator.com before applying. Coverage varies based on paver porosity and joint size. Specifications are subject to change by the manufacturer.
How Much Alliance Gator Hybrid Seal Low Gloss Do You Need?
Coverage depends on whether you are using it as a stand alone sealer over polymeric sand, or as a joint sand stabilizer with ASTM C144 sand.
Per gallon as stand alone sealer
1 Gallon
~200 sq ft
5 Gallon
~1,000 sq ft
8 oz Sample
~25 sq ft
Per gallon as joint sand stabilizer (ASTM C144 sand)
1 Gallon
~100 sq ft
5 Gallon
~500 sq ft
8 oz Sample
~12 sq ft
Size
Stand Alone Sealer
Joint Sand Stabilizer
1 Gallon
~200 sq ft
~100 sq ft
5 Gallon
~1,000 sq ft
~500 sq ft
8 oz Sample
~25 sq ft
~12 sq ft
Coverage varies by paver porosity and joint width. Stand alone coverage applies when used over polymeric sand. Joint stabilizer coverage applies when used with ASTM C144 sand. Not sure how many gallons you need? Call us at (856) 418-4895.
Why Buy Alliance Gator Hybrid Seal Low Gloss from Polymeric Sand Store?
Alliance makes excellent products and we carry them because we believe in them. Here is what you get when you order Alliance Gator Hybrid Seal Low Gloss from Polymeric Sand Store.
Same day shipping on every order Order Alliance Gator Hybrid Seal Low Gloss before 2 PM Eastern time and your order ships today. We ship to the continental United States every day.
Real expert advice available 24 hours a day, 7 days a week Call or text (856) 418-4895 any time. Not sure if Alliance Gator Hybrid Seal Low Gloss is the right finish for your pavers, or whether you need Satin Look, Natural Look, or Resealer? We will help you make the right choice before you order.
Full Alliance product line available We carry the complete Alliance line including all polymeric sands, jointing materials, cleaners, and sealers. Order Alliance Gator Hybrid Seal Low Gloss together with Gator Shampoo, Gator Efflorescence Cleaner, and your polymeric sand in one shipment.
Coverage calculation support Alliance Gator Hybrid Seal Low Gloss coverage varies by paver porosity and joint width. Call us and we will help you calculate how many gallons you need before you order so you are not short on a job.
30 day satisfaction guarantee If something is wrong with your order, contact us within 30 days and we will make it right. We accept returns on items that are unopened, unused, and in their original packaging. You can return the product for a full refund, or contact us for a pre-paid return label which will be deducted from your refund.
Frequently Asked Questions: Alliance Alliance Gator Hybrid Seal Low Gloss Water Based Paver Sealer
All three are acrylic based paver sealers that provide the same protection against oil, dirt, de icing salt, and UV damage. The difference is finish appearance only. Natural Look leaves pavers looking exactly as they do unsealed. no sheen at all. Alliance Gator Hybrid Seal Low Gloss delivers a low gloss high gloss wet finish that enhances color slightly. Wet Look provides a high gloss finish that makes pavers look wet and dramatically deepens the color. Most homeowners choose Wet Look as the balanced option. Call us at (856) 418-4895 and we can help you choose.
No. Alliance Gator Hybrid Seal Low Gloss is specifically formulated for unsealed surfaces only and cannot be used as a resealer over an existing sealer coating. If your pavers are already sealed, you need Gator Seal Resealer, which is designed to penetrate and reactivate an existing sealer. Applying Alliance Gator Hybrid Seal Low Gloss over an existing sealer will result in poor adhesion and sealer failure.
Wait at least 60 days after new paver installation before applying Alliance Gator Hybrid Seal Low Gloss. New concrete pavers need time to fully cure and off-gas before sealing. Sealing too early can trap moisture inside the paver, cause discoloration, or prevent the sealer from properly bonding to the surface. Always consult the paver manufacturer for their specific recommendation on when to seal.
The application process requires spraying the sealer onto the surface in 60 sq ft sections and then immediately back rolling with a water based foam roller (yellow) to remove excess sealer. This must happen quickly before the sealer begins to cure. With one person, it is very difficult to spray and back roll fast enough to avoid uneven application or pooling. With two people. one spraying and one rolling. the process moves efficiently and the finish comes out consistent and even.
Coverage is approximately 200 sq ft per gallon as a stand alone sealer, though this varies based on paver porosity and joint width. More porous pavers and wider joints absorb more sealer and reduce coverage. For a 500 sq ft patio, plan for approximately 3 gallons. For a 900 sq ft driveway, the 5 gallon size will typically cover the full area. Call us at (856) 418-4895 and we will help you calculate the right amount before you order.
Orders placed before 2 PM Eastern time ship the same day. We keep Alliance Gator Hybrid Seal Low Gloss in both the 1 gallon and 5 gallon sizes in stock and ship to homeowners and contractors across the continental United States. For questions about your order, call or text us at (856) 418-4895.
Questions About Alliance Alliance Gator Hybrid Seal Low Gloss Water Based Paver Sealer?
Call or text us 24/7 at (856) 418-4895. Not sure which sealer finish is right for your pavers? We will help you choose between Wet Look, Wet Look, Natural Look, and Resealer before you order. Orders placed before 2 PM Eastern time ship the same day.
