Alliance Designer Products · Sold by Polymeric Sand Store
Gator Maxx Sand Polymeric Sand
Alliance's original high-performance polymeric sand for paver joints up to 2 inches. Works on both traditional base and concrete slab overlays. Advanced haze free technology with rain safe in 1 hour.
Alliance Gator Maxx Sand is the original high-performance polymeric sand. the product that established Alliance as a leader in the paver jointing market. Alliance Gator Maxx Sand is a proven, trusted formula for paver joints up to 2 inches wide that works on both traditional gravel base and concrete slab overlay applications.
Gator Maxx Sand uses Alliance's advanced haze free polymer binder technology. When activated with water, the Alliance Gator Maxx Sand polymer binders set firmly into the joint, becoming very firm while retaining the flexibility needed to handle freeze thaw cycles without cracking. Alliance Gator Maxx Sand is rain safe in 1 hour on a traditional base and 24 hours on an overlay. Note that a leaf blower is required during installation to remove surface residue before watering. this distinguishes it from the newer G2-formula products.
Available in Beige and Slate Grey. Ideal for concrete pavers, natural stone, and wet cast products on traditional and overlay bases. If you need joints wider than 2 inches, Gator Maxx G2 handles up to 4 inches. If you want the G2 no-blower formula for joints up to 2 inches, consider Gator Super Sand G2.
Not sure which polymeric sand is right for your project? Call or text us 24/7 at (856) 418-4895 and we will help you choose the correct product for your joint width, paver type, and base.
Beige
Slate Grey
Is Alliance Gator Maxx Sand the Right Polymeric Sand for Your Project?
Patio pavers on a traditional gravel base Ideal for standard interlocking concrete paver patios with joints up to 2 inches wide on a properly prepared traditional gravel base system.
Overlay installations on existing concrete slabs Compatible with overlay applications over concrete slabs for joints up to 2 inches. Drainage holes (2 inch diameter, approximately 10 feet apart at lowest slab elevations) must be pre-drilled, filled with 3/8 inch stone, and covered with Gator Fabric GF4.4.
Pool decks and pool surrounds Recommended for in-ground pool installations on traditional and overlay bases. Requires a minimum 1/8 inch per foot slope away from the pool. Pool coping joints must use mortar. Gator Maxx Sand is for the surrounding paver field only.
Paver driveways and parking areas Handles full vehicular and pedestrian traffic on a traditional gravel base. Sand level must be at least 1/8 inch below the paver surface or chamfer edge. All pavers must be fully interlocked. Fanned pavers do not qualify for vehicular use.
Walkways, footpaths, and commercial streetscapes Approved for a wide range of pedestrian and commercial hardscape applications including steep slopes and high-traffic areas.
Concrete pavers, natural stone, and wet cast products Works across all standard interlocking surfaces. ASTM C144 gradation handles both tight and wider joints up to 2 inches.
Gator Base applications Compatible for use in Gator Base installations per Alliance manufacturer guidelines.
Open-graded aggregate bases that lock or choke Can be applied when pavers are installed on aggregates that lock or choke themselves. Do not use on aggregates with large open voids.
What Makes Alliance Gator Maxx Sand Different from Regular Paver Sand?
Advanced haze free polymer technology Alliance Gator Maxx Sand's proven polymer binder formula prevents white haze residue from forming on paver faces after activation.
Overlay compatible Alliance Gator Maxx Sand is one of the only Alliance polymeric sands approved for pavers installed over existing concrete slabs. Works on both traditional and overlay applications for joints up to 2 inches.
Rain safe in 1 hour Alliance Gator Maxx Sand is rain safe just 1 hour after water activation on a traditional drainage base. On an overlay, rain safe after 24 hours.
Firm yet flexible cure Once set, Alliance Gator Maxx Sand becomes very firm and locks securely between the paver joints while retaining enough flexibility to expand and contract with seasonal temperature changes without cracking.
ASTM C144 gradation Works in joints from the tightest 1/8 inch all the way up to 2 inches wide on both traditional and overlay bases.
OSHA crystalline silica compliant Meets OSHA 29 CFR 1926.1153 requirements. Safe for professional contractor use on any job site.
Waterproof bag packaging Store bags lying flat with the front facing up. Sealed intact bags and pallets can be safely stored outdoors until needed.
Note: Unlike the G2-formula products, Alliance Gator Maxx Sand requires a leaf blower step to clear residue from the paver surface before water activation. Factor this into your installation plan and have a leaf blower ready on the job.
What Alliance Gator Maxx Sand Polymeric Sand Helps Prevent
A properly installed polymeric sand joint is your best long term defense against the most common paver maintenance problems. Here is what Gator Maxx Sand keeps out:
Weeds growing through paver joints Polymer-locked joints leave no loose soil for weed seeds to take root, making weed growth through the pavers rare with a properly installed joint.
Ant tunneling and insect damage Ants cannot tunnel through a fully cured polymeric sand joint, preventing the base destabilization that causes pavers to sink and shift over time.
Joint erosion and washout from rain and wind Regular paver sand washes out after heavy rain. Alliance Gator Maxx Sand's polymer bond holds the jointing material firmly in place against rain, wind, and surface runoff.
Freeze-thaw cracking Alliance Gator Maxx Sand remains flexible after curing, allowing it to expand and contract with seasonal temperature changes without cracking out of the joint.
Paver shifting and movement Tightly locked joints keep the entire paver surface stable under foot traffic, vehicular loads, and ground movement throughout the seasons.
White haze residue on paver faces The advanced haze free polymer technology prevents white residue on the paver surface when installed correctly on completely dry pavers.
Note: Gator Maxx Sand does not prevent moss, mold, or mildew. Those result from shade, moisture retention, and drainage conditions on site. Treat with a paver-safe cleaner and improve drainage to address them.
Alliance Gator Maxx Sand Polymeric Sand Available Colors
Gator Maxx Sand is available in two colors: Beige and Slate Grey. What you see on a screen looks different on your actual pavers in real outdoor light. We strongly recommend ordering physical color samples before purchasing full bags to confirm the right match for your project.
Not sure which color matches your pavers?Order our sample pack with both colors shipped to you. Test them on your actual pavers in real outdoor light before purchasing full bags. The right color choice makes a significant difference in the finished look of your project.
How Many Bags of Alliance Gator Maxx Sand Polymeric Sand Do You Need?
Alliance Gator Maxx Sand polymeric sand coverage per 50 lb bag depends on your joint width and paver size. Numbers below are sourced directly from the official Alliance Gator Technical Data Sheet. Always order 10 to 15 percent extra to account for waste and variation.
Narrow joints (1/8" to 3/8") per 50 lb bag
Beige, Slate Grey
65–85 ft²
Wide joints (3/4" to 1-1/4") per 50 lb bag
Beige, Slate Grey
22–42 ft²
Color
Narrow joints (1/8" to 3/8")
Wide joints (3/4" to 1-1/4")
Beige
65 to 85 sq ft
22 to 42 sq ft
Slate Grey
65 to 85 sq ft
22 to 42 sq ft
Minimum joint depth: 1-1/2 inches (38 mm). The entire joint depth must be filled with Alliance Gator Maxx Sand Polymeric Sand. Coverage based on standard pavers 2-3/8 inches (6 cm) tall. Actual coverage varies by joint width, depth, and paver size. Always order 10 to 15 percent extra. Source: Alliance Gator official TDS.
Important: Unlike the G2-formula products, Alliance Gator Maxx Sand requires a leaf blower step before water activation. Have a leaf blower ready before you start.
1
Confirm everything is completely dry
Both the paver surfaces and the joints must be completely dry before you begin. Any moisture will prematurely activate the polymers, causing them to stick to the paver surface. Wait for a fully dry day. Pavers that have been pressure washed or rained on need at least 24 to 48 hours to dry completely.
Overlay installs: drainage holes (2 inch diameter, spaced approximately 10 feet apart at the lowest slab elevations) must be in place, filled with 3/8 inch stone, and covered with a 1 ft x 1 ft patch of Gator Fabric GF4.4 before applying.
2
Spread and sweep polymeric sand into all joints
Pour Alliance Gator Maxx Sand onto the dry paver surface and use a hard bristle broom to sweep it into the joints in multiple directions. Work in sections and make multiple passes to ensure full joint penetration. Leave a layer of sand on top of the pavers for the compaction step. Narrow joints require extra sweeping passes to fill completely.
3
Compact with a plate compactor
Run a vibratory plate compactor to compact Alliance Gator Maxx Sand equipped with a rubber protective pad over the entire paved surface. Work in multiple directions to eliminate air pockets and fully pack the joints. After compacting, sweep additional sand into any joints that need topping off, then compact again. The final sand level must sit at least 1/8 inch below the top of the paver surface or 1/8 inch below the chamfer edge.
On textured or pre-finished paver surfaces: clear all sand from the paver face before compacting to avoid scratching or damaging the surface finish.
4
Sweep off surface excess then use a leaf blower
Use a hard bristle broom followed by a soft broom to remove the majority of remaining sand from the paver surfaces. Then use a leaf blower to clear all remaining Gator Maxx Sand residue from the paver face. Work in manageable sections of approximately 100 square feet. This step is required and must be completed before watering.
5
Activate with water. shower setting, section by section
Set your hose nozzle to the shower setting. Start at the lowest point of the installation and work upward. Water each 30 square foot section for approximately 30 seconds until the sand repels the water and it begins pooling on the joints. Move immediately to the next section. Do not over water or allow the surface to dry out during the activation phase. Standing water will wash sand out of the joints.
On slopes and pool surrounds: always start watering at the lowest point and work upward. Starting at the top will pull sand downhill and cause uneven activation.
6
Stay off until fully cured
On a traditional gravel base, the installation is rain safe in 1 hour. On an overlay installation, rain safe after 24 hours. Keep foot traffic and vehicles off until the joints are fully cured. The joints will develop a firm crust on top after curing which is completely normal and by design.
Do not apply if any of these conditions exist
Paver surfaces or joints are damp or wet in any way
Temperature is at or below 32°F (0°C)
Rain is expected within 1 hour of water activation on traditional base, or within 24 hours on an overlay
Pavers are installed on aggregates with large open voids, as the sand will migrate through
Pavers are installed on asphalt. Do not sweep Gator Maxx Sand over asphalt surfaces
Pavers are fanned rather than fully interlocked. Fanned pavers do not qualify for vehicular use
Long Term Maintenance for Alliance Gator Maxx Sand Polymeric Sand Paver Joints
Alliance Gator Maxx Sand polymeric sand is significantly lower maintenance than regular paver joint sand, but it is not completely maintenance free. Here is exactly what to do to keep your paver joints in top condition for years to come.
Routine cleaning Apply Gator Shampoo or a paver-safe cleaner to the full paver surface including the joints. Rinse with a garden hose on the shower setting at standard residential water pressure, typically up to 80 psi. No pressure washer is required or recommended directly on the joints.
White haze on pavers Usually caused by efflorescence from the pavers triggered during water activation, or by polymer residue from applying on a surface that was not fully dry. Treat with Gator Efflorescence Cleaner. The haze also fades naturally over time with weathering and sun exposure.
Moss, mold, or mildew These are drainage and shade issues, not a sand problem. Treat the surface with a paver-safe cleaner. For long term prevention, improve drainage and reduce shade over the paved area.
Re-sanding worn joints Remove all old jointing material completely before re applying. Do not apply new Alliance Gator Maxx Sand on top of old polymeric sand. Pavers must be fully dry before starting. Then follow the standard six-step installation process from the beginning.
Storing leftover bags Alliance Gator Maxx Sand comes in waterproof bags. Lay bags flat with the front facing up. Sealed intact bags and intact pallets can be safely stored outdoors until needed.
Leaf blower requiredYes. required before water activation
Colors availableBeige, Slate Grey
Bag weight50 lbs (22.7 kg)
Bag packagingWaterproof bag, store flat, outdoor safe
ManufacturerAlliance Designer Products Inc.
All specifications sourced from the official Alliance Gator Technical Data Sheet (TDS). Always verify the latest TDS at AllianceGator.com before installation. Specifications are subject to change by the manufacturer.
Alliance makes excellent products. We carry them because we believe in them. Here is what you get when you order from Polymeric Sand Store that you will not find buying from Alliance directly, at a big box store, or on Amazon.
Same-day shipping on every order Order before 2 PM Eastern time and your polymeric sand ships today. Alliance does not sell direct to consumers. Home Depot and Amazon take days. We ship the same day, every day, to the continental United States.
Real expert advice available 24 hours a day, 7 days a week Call or text (856) 418-4895 any time. Tell us your joint width, paver type, and base, and we will tell you exactly which sand to order and how many bags you need.
Physical color samples before you commit We offer Beige and Slate Grey as physical 2 oz sample bags shipped directly to you. Test them on your actual pavers in real outdoor light before purchasing full bags.
Multi-brand expert selection We carry Alliance, Techniseal, Rhino, SEK, and more. We will give you an honest recommendation for your specific project, even if the right answer is a different product.
Free polymeric sand calculator Enter your dimensions and joint width, and we will calculate exactly how many bags to order. No guesswork and no over buying.
30-day satisfaction guarantee If something is wrong with your order, contact us within 30 days and we will make it right. We accept returns on items that are unopened, unused, and in their original packaging. You can return the product for a full refund, or contact us for a pre-paid return label which will be deducted from your refund.
The main differences between Alliance Gator Maxx Sand and Gator Maxx G2 are the polymer technology, the joint width capacity, and the installation process. Gator Maxx Sand uses Alliance's original haze free polymer binder formula and handles joints up to 2 inches on both traditional and overlay bases, but requires a leaf blower step during installation. Gator Maxx G2 uses the newer second generation intelligent polymer technology, handles joints up to 4 inches on traditional base and up to 2 inches on overlay, and does not require a leaf blower. If you want to avoid the blower step or need joints wider than 2 inches, Maxx G2 is the better choice. Call us at (856) 418-4895 if you are not sure.
Yes. Alliance Gator Maxx Sand is compatible with overlay applications on existing concrete slabs for joints up to 2 inches wide. This is different from Super Sand Bond and Super Sand G2 which cannot be used on overlays. Drainage holes (2 inch diameter, spaced approximately 10 feet apart at the lowest slab elevations) must be pre-drilled, filled with 3/8 inch stone, and covered with Gator Fabric GF4.4. Rain safe time on overlays is 24 hours after activation.
Yes. Unlike the G2-formula products, Alliance Gator Maxx Sand requires a leaf blower step to remove all surface residue from the paver face before water activation. This is a required step in the installation process. Make sure you have a leaf blower available before starting your project. If you prefer to skip the blower step, consider Gator Super Sand G2 (joints up to 2 inches) or Gator Maxx G2 (joints up to 4 inches) which are both blower-free.
Alliance Gator Maxx Sand is rain safe 1 hour after water activation on a traditional gravel base. On an overlay installation over a concrete slab, it is rain safe after 24 hours. Plan your project accordingly and check the weather forecast before starting.
Yes, this is completely normal and it is exactly how the product is designed to perform. The cured top layer forms a firm protective crust that spans from chamfer edge to chamfer edge. The densely compacted sand below provides the structural support. This is not a sign of installation failure.
White residue is almost always efflorescence from the pavers triggered by water activation, or polymer residue from applying on a surface that was not completely dry or from not completing the leaf blower step before watering. Both respond well to Gator Efflorescence Cleaner. The haze also fades naturally over time. Call us at (856) 418-4895 if the problem persists.
No. This is strongly advised against by both the manufacturer and our team. The entire joint depth of at least 1-1/2 inches must be filled with Gator Maxx Sand. If regular paver sand is used below, water and ice will penetrate from underneath and push the polymeric sand layer out over time, causing the joint to fail prematurely.
Orders placed before 2 PM Eastern time ship the same day. We keep Gator Maxx Sand in both Beige and Slate Grey in stock at all times and ship to homeowners and contractors across the continental United States. For questions about your order, call or text us at (856) 418-4895.
You can order Gator Maxx Sand directly from Polymeric Sand Store and have it delivered fast. Orders placed before 2 PM Eastern time ship the same day. We serve homeowners and hardscape contractors in New Jersey, Pennsylvania, New York, Delaware, Maryland, and the entire continental United States. Both colors are in stock and available to ship now.
Questions About Alliance Gator Maxx Sand Polymeric Sand?
Call or text us 24/7 at (856) 418-4895. We will tell you exactly whether Alliance Gator Maxx Sand polymeric sand is right for your project, how many bags you need, and what to watch out for. Orders placed before 2 PM Eastern time ship the same day. Both colors are in stock.
