Alliance Designer Products · Sold by Polymeric Sand Store
Gator Super Sand Bond Polymeric Sand
The high-performance jointing sand for tight paver joints up to 1 inch on a traditional base. Advanced haze free technology, rain safe in 1 hour, and no blower required.
Rain Safe in 1 HourNo Dust · No Haze · No BlowerASTM C144 · OSHA Compliant
1"Max joint width
2 colorsAvailable
What Is Alliance Gator Super Sand Bond Polymeric Sand?
Alliance Gator Super Sand Bond is a high-performance polymeric sand for tight paver joints up to 1 inch wide. Alliance Gator Super Sand Bond is the go-to choice when your joints are narrow and you want a long lasting, haze free result with no blower and no complicated application process.
Unlike the G2-formula sands, Alliance Gator Super Sand Bond uses Alliance's advanced haze free polymer binder technology. a proven formula that sets firmly into the joint, becomes very firm once cured, and retains enough flexibility to handle freeze thaw cycles without cracking out. Alliance Gator Super Sand Bond is rain safe in just 1 hour after water activation on a traditional drainage base.
Available in Beige and Slate Grey. Works with concrete pavers, natural stone, and wet cast products on a traditional gravel base. If your joints exceed 1 inch, consider Gator Super Sand G2 (up to 2 inches) or Gator Maxx G2 (up to 4 inches).
Not sure if Super Sand Bond is right for your project? Call or text us 24/7 at (856) 418-4895 and we will tell you exactly which sand fits your joint width and base type.
Beige
Slate Grey
Is Alliance Gator Super Sand Bond the Right Polymeric Sand for Your Project?
Not compatible with overlay (concrete slab) installations. If your pavers are installed over an existing concrete slab, Super Sand Bond cannot be used. You need Gator Maxx G2 for overlay applications.
Patio pavers with joints up to 1 inch The ideal choice for standard interlocking concrete paver patios with tight joints on a properly prepared gravel base system.
Pool decks and pool surrounds Recommended for in-ground pool installations on a traditional base. Requires a minimum 1/8 inch per foot slope away from the pool. Pool coping joints must use mortar. Super Sand Bond is for the surrounding paver field only.
Paver driveways and parking areas Handles full vehicular and pedestrian traffic on a traditional gravel base. Sand level must be at least 1/8 inch below the paver surface or chamfer edge. All pavers must be fully interlocked. Fanned pavers do not qualify for vehicular use.
Walkways, footpaths, and commercial streetscapes Approved for a wide range of pedestrian and commercial hardscape applications including steep slopes and high-traffic areas on traditional base.
Concrete pavers, natural stone, and wet cast products Works across all standard interlocking surfaces on a traditional gravel base. ASTM C144 fine gradation handles even the tightest 1/8 inch joints.
Clay pavers Can be used on clay pavers but they must be 100 percent completely dry before application. Always test a small area first.
Open-graded aggregate bases that lock or choke Can be applied when pavers are installed on aggregates that lock or choke themselves. Do not use on aggregates with large open voids.
What Makes Alliance Gator Super Sand Bond Different from Regular Paver Sand?
Advanced haze free polymer technology Alliance Gator Super Sand Bond's polymer binder formula prevents white haze residue from forming on paver faces during and after application.
No blower required Alliance Gator Super Sand Bond stays in the joints during application. No leaf blower step needed, saving time and cleanup effort on every job.
Rain safe in 1 hour On a traditional drainage base, the installation is rain safe just 1 hour after water activation. Plan your project with confidence even when weather is unpredictable.
Firm yet flexible cure Once set, Alliance Gator Super Sand Bond becomes very firm and locks securely between the paver joints while retaining enough flexibility to expand and contract with seasonal temperature changes without cracking.
Alerts you when to stop watering Alliance Gator Super Sand Bond has a built-in visual cue. the surface changes appearance when enough water has been applied, so you know exactly when to stop. No guesswork.
ASTM C144 fine gradation Works in joints from the tightest 1/8 inch all the way up to 1 inch wide, making it the right choice for most standard tight joint residential paver installations.
OSHA crystalline silica compliant Meets OSHA 29 CFR 1926.1153 requirements. Safe for professional contractor use on any job site.
Waterproof bag packaging Store bags lying flat with the front facing up. Sealed intact bags can be safely stored outdoors on a pallet until needed.
What Alliance Gator Super Sand Bond Polymeric Sand Helps Prevent
A properly installed polymeric sand joint is your best long term defense against the most common paver maintenance problems. Here is what Super Sand Bond keeps out:
Weeds growing through paver joints Polymer-locked joints leave no loose soil for weed seeds to take root, making weed growth through the pavers rare.
Ant tunneling and insect damage Ants cannot tunnel through a fully cured polymeric sand joint, preventing the base destabilization that causes pavers to sink and shift over time.
Joint erosion and washout from rain and wind Regular paver sand washes out after heavy rain. Alliance Gator Super Sand Bond's polymer formula holds the jointing material firmly in place against rain, wind, and surface runoff.
Freeze-thaw cracking Alliance Gator Super Sand Bond remains flexible after curing, allowing it to expand and contract with seasonal temperature changes without cracking out of the joint.
Paver shifting and movement Tightly locked joints keep the entire paver surface stable under foot traffic, vehicular loads, and ground movement throughout the seasons.
White haze and dust residue on paver faces Advanced haze free polymer technology prevents white residue from forming on the paver surface during and after application.
Note: Super Sand Bond does not prevent moss, mold, or mildew. Those result from shade, moisture retention, and drainage conditions on site. Treat with a paver-safe cleaner and improve drainage to address them.
Alliance Gator Super Sand Bond Polymeric Sand Available Colors
Super Sand Bond is available in two colors: Beige and Slate Grey. What you see on a screen looks different on your actual pavers in real outdoor light. We strongly recommend ordering physical color samples before purchasing full bags to confirm the right match for your project.
Not sure which color matches your pavers?Order our sample pack with both colors shipped to you. Test them on your actual pavers in real outdoor light before purchasing full bags. The right color choice makes a significant difference in the finished look of your project.
How Many Bags of Gator Super Sand Bond Do You Need?
Alliance Gator Super Sand Bond coverage per 50 lb bag depends on your joint width. Numbers below are sourced directly from the official Alliance Gator Technical Data Sheet for standard 2-3/8 inch (6 cm) paver height. Always order 10 to 15 percent extra to account for waste and variation.
Narrow joints (1/8" to 3/8") per 50 lb bag
Beige, Slate Grey
65–85 ft²
Wide joints (3/4" to 1-1/4") per 50 lb bag
Beige, Slate Grey
22–42 ft²
Per 50 lb (22.7 kg) bag (Paver 2-3/8" (6 cm) in height)
Narrow joints 1/8" to 3/8"
Wide joints 3/4" to 1-1/4"
Beige, Slate Grey
65 to 85 sq ft
22 to 42 sq ft
Minimum joint depth: 1-1/2 inches (38 mm). The entire joint depth must be filled with Super Sand Bond. Coverage based on standard pavers 2-3/8 inches (6 cm) tall. Actual coverage varies by joint width, depth, and paver size. Always order 10 to 15 percent extra. Source: Alliance Gator official TDS.
How to Install Alliance Gator Super Sand Bond Polymeric Sand
Always refer to the latest Alliance Gator Super Sand Bond Technical Data Sheet (TDS) before installing. Pavers must be installed per ICPI Tech Spec No. 2. Alliance Gator Super Sand Bond is for traditional base installations only. Do not use on overlay applications over concrete slabs.
1
Confirm everything is completely dry
The single most common installation mistake is starting on pavers that are not fully dry. Any moisture, including damp joints, will prematurely activate the polymers and cause them to stick to the paver surface. Wait for a fully dry day. Pavers that have been pressure washed or rained on need at least 24 to 48 hours to dry completely. Both the paver surfaces and the joints must be bone dry before you begin.
2
Spread and sweep polymeric sand into all joints
Pour Super Sand Bond onto the dry paver surface and use a hard bristle broom to sweep it into the joints in multiple directions. Work in sections and make multiple passes to ensure full joint penetration. Leave a thin layer of sand on top of the pavers for the compaction step.
3
Compact with a plate compactor
Run a vibratory plate compactor equipped with a rubber protective pad over the entire paved surface. Work in multiple directions to eliminate air pockets and fully pack the joints. After compacting, sweep additional sand into any joints that need topping off, then compact again. The final sand level must sit at least 1/8 inch below the top of the paver surface or 1/8 inch below the chamfer edge.
On textured or pre-finished paver surfaces: clear all sand from the paver face before compacting to avoid scratching or damaging the surface finish.
4
Sweep off all surface excess. no leaf blower needed
Use a hard bristle broom followed by a soft broom to remove all remaining sand from the paver surfaces. No leaf blower step is required. Super Sand Bond's haze free formula stays in the joints and does not leave residue that needs to be blown off.
5
Activate with water. shower setting, section by section
Set your hose nozzle to the shower setting. Start at the lowest point of the installation and work upward. Water each section until the surface signals it has received enough water. Super Sand Bond will visually indicate when activation is complete. Do not over water. Standing water will wash sand out of the joints.
On slopes and pool surrounds: always start watering at the lowest point and work upward. Starting at the top will pull sand downhill and cause uneven activation.
6
Stay off until fully cured
The installation is rain safe in 1 hour on a traditional gravel base. Keep foot traffic and vehicles off until the joints are fully cured. The joints will develop a firm crust on top after curing. This is completely normal and by design.
Do not apply if any of these conditions exist
Paver surfaces or joints are damp or wet in any way
Temperature is at or below 32°F (0°C)
Rain is expected within 1 hour of water activation
Pavers are installed on aggregates with large open voids, as the sand will migrate through
Pavers are installed on asphalt. Do not sweep Super Sand Bond over asphalt surfaces
Pavers are installed over an existing concrete slab. Use Gator Maxx G2 for overlay applications
Pavers are fanned rather than fully interlocked. Fanned pavers do not qualify for vehicular use
Clay pavers that are not 100 percent completely dry
Long Term Maintenance for Gator Super Sand Bond Polymeric Sand Paver Joints
Alliance Gator Super Sand Bond polymeric sand is significantly lower maintenance than regular paver joint sand, but it is not completely maintenance free. Here is exactly what to do to keep your paver joints in top condition for years to come.
Routine cleaning Apply Gator Shampoo or a paver-safe cleaner to the full paver surface including the joints. Rinse with a garden hose on the shower setting at standard residential water pressure, typically up to 80 psi. No pressure washer is required or recommended directly on the joints.
White haze on pavers Usually caused by efflorescence from the pavers themselves triggered during water activation, or by polymer residue from applying on a surface that was not fully dry. Treat with Gator Efflorescence Cleaner. The haze also fades naturally over time with weathering and sun exposure.
Moss, mold, or mildew These are drainage and shade issues, not a sand problem. Treat the surface with a paver-safe cleaner. For long term prevention, improve drainage and reduce shade over the paved area.
Re-sanding worn joints Remove all old jointing material completely before re applying. Do not apply new Alliance Gator Super Sand Bond on top of old polymeric sand. Pavers must be fully dry before starting. Then follow the standard six-step installation process from the beginning.
Storing leftover bags Super Sand Bond comes in waterproof bags. Lay bags flat with the front facing up. Sealed intact bags can be safely stored outdoors on a pallet until needed.
Technical Specifications. Alliance Gator Super Sand Bond Polymeric Sand
Minimum joint width1/8 inch (3 mm)
Maximum joint width1 inch (2.5 cm). traditional base only
Overlay (concrete slab) applicationsNot compatible. Use Gator Maxx G2.
Minimum joint depth1-1/2 inches (38 mm)
Minimum sand level below paver surface1/8 inch below surface or chamfer edge
Minimum install temperatureAbove 32°F (0°C)
Rain safe. traditional base1 hour after activation
Coverage. narrow joints (1/8" to 3/8")65 to 85 sq ft per bag
Coverage. wide joints (3/4" to 1-1/4")22 to 42 sq ft per bag
Bag packagingWaterproof bag, store flat, outdoor safe
ManufacturerAlliance Designer Products Inc.
All specifications sourced from the official Alliance Gator Technical Data Sheet (TDS). Always verify the latest TDS at AllianceGator.com before installation. Specifications are subject to change by the manufacturer.
Why Buy Alliance Gator Super Sand Bond Polymeric Sand from Polymeric Sand Store?
Alliance makes excellent products. We carry them because we believe in them. Here is what you get when you order from Polymeric Sand Store that you will not find buying from Alliance directly, at a big box store, or on Amazon.
Same-day shipping on every order Order before 2 PM Eastern time and your polymeric sand ships today. Alliance does not sell direct to consumers. Home Depot and Amazon take days. We ship the same day, every day, to the continental United States.
Real expert advice available 24 hours a day, 7 days a week Call or text (856) 418-4895 any time. Tell us your joint width, paver type, and base, and we will tell you exactly which sand to order and how many bags you need.
Physical color samples before you commit We offer Beige and Slate Grey as physical 2 oz sample bags shipped directly to you. Test them on your actual pavers in real outdoor light before purchasing full bags.
Multi-brand expert selection We carry Alliance, Techniseal, Rhino, SEK, and more. We will give you an honest recommendation for your specific project, even if the right answer happens to be a different product.
Free polymeric sand calculator Enter your dimensions and joint width, and we will calculate exactly how many bags to order. No guesswork and no over buying.
30-day satisfaction guarantee If something is wrong with your order, contact us within 30 days and we will make it right. Unused product in original packaging qualifies for a full return. We stand behind every single order with no runaround and no hassle.
Frequently Asked Questions. Gator Super Sand Bond Polymeric Sand
The key difference is the polymer technology and joint width capacity. Super Sand Bond uses Alliance's original advanced haze free polymer binder formula and handles joints up to 1 inch wide. Super Sand G2 uses the newer second generation intelligent polymer technology and handles joints up to 2 inches wide. Both are for traditional base installations only with no overlay capability. If your joints are under 1 inch, Super Sand Bond is a reliable and proven choice. If your joints are between 1 and 2 inches, Super Sand G2 is the right product. Not sure? Call us at (856) 418-4895.
No. Alliance Gator Super Sand Bond is not approved for overlay installations on concrete slabs. If your pavers are installed over an existing concrete slab, you must use Gator Maxx G2 instead. Maxx G2 is the only Alliance polymeric sand specifically engineered for overlay applications.
Alliance Gator Super Sand Bond is rain safe 1 hour after water activation on a traditional gravel base. This is longer than the G2-formula sands which are rain safe in 15 minutes, so plan your installation accordingly and check the weather forecast before starting.
Yes, this is completely normal and it is exactly how the product is designed to perform. The cured top layer forms a firm protective crust that spans from chamfer edge to chamfer edge. The densely compacted sand below provides the structural support. This is not a sign of installation failure.
White residue after installation is almost always efflorescence from the pavers themselves triggered by water activation, or polymer residue from applying on a surface that was not completely dry. Both respond well to Gator Efflorescence Cleaner. The haze also fades naturally over time with weather exposure. Call us at (856) 418-4895 if the problem persists after treatment.
No. This is strongly advised against by both the manufacturer and our team. The entire joint depth of at least 1-1/2 inches must be filled with Super Sand Bond. If regular paver sand is used below, water and ice will penetrate from underneath and push the polymeric sand layer out over time, causing the joint to fail prematurely.
No. Super Sand Bond's haze free formula does not leave residue on the paver face, so a standard broom sweep before watering is all that is needed. No blower, no extra equipment, and no additional cleanup time.
Polymeric sand is jointing sand mixed with polymer binders. When activated with water, those polymers harden the sand inside the joint, locking pavers firmly in place and resisting weeds, insects, and erosion. Regular paver sand has no binders, so it washes out after rain, allows ants to burrow freely through the joints, and requires constant replenishment. Polymeric sand is a long lasting solution when installed correctly on the right base type.
Orders placed before 2 PM Eastern time ship the same day. We keep Gator Super Sand Bond in both Beige and Slate Grey in stock at all times and ship to homeowners and contractors across the continental United States. For questions about your order, call or text us at (856) 418-4895.
You can order Gator Super Sand Bond directly from Polymeric Sand Store and have it delivered fast. Orders placed before 2 PM Eastern time ship the same day. We serve homeowners and hardscape contractors in New Jersey, Pennsylvania, New York, Delaware, Maryland, and the entire continental United States. Both colors are in stock and available to ship now.
Questions About Alliance Gator Super Sand Bond Polymeric Sand?
Call or text us 24/7 at (856) 418-4895. We will tell you exactly whether Alliance Gator Super Sand Bond polymeric sand is right for your project, how many bags you need, and what to watch out for. Orders placed before 2 PM Eastern time ship the same day. Both colors are in stock.
The process to order and receive the sand was effortless, and the sand was much better quality than other patio sand that I’ve used. I’ll always re-order this product in the future.
F
Felix Okor
Product arrived well packed and on time. Highly recommend this seller.
S
Sam Knisley
good product
worked as advertised for re-doing the joints between my patio pavers. Lots of work but directions must be followed to have good results.
