Alliance Designer Products · Sold by Polymeric Sand Store
Gator Super Sand G2 Intelligent Polymeric Sand
Alliance Gator Super Sand G2 polymeric sand is the smart choice for standard paver joint widths up to 2 inches on a traditional base. Alliance Gator Super Sand G2 has no dust, no haze, and no blower required. One watering activates it and it is rain safe in just 15 minutes.
Rain Safe in 15 MinNo Dust · No Haze · No BlowerASTM C144 · OSHA Compliant
2"Max joint width
2 colorsAvailable
What Is Alliance Gator Super Sand G2 Polymeric Sand?
Gator Super Sand G2 is the go-to polymeric sand for standard paver joint installations on a traditional gravel base. If your joints are between 1/8 inch and 2 inches wide and your pavers are laid on a conventional base system, Super Sand G2 delivers everything you need: no dust, no haze, no leaf blower, and rain safe in 15 minutes after activation.
Like all G2-formula sands from Alliance, Super Sand G2 uses second generation intelligent polymers that neutralize dust and haze during application. When activated with water, those polymers bind the sand firmly into the joint, creating a locked, flexible joint that resists weeds, insects, erosion, and freeze thaw damage for years.
Super Sand G2 is available in Beige and Slate Grey. It is ideal for concrete pavers, natural stone, wet cast products, and clay pavers on a traditional base. If your joints exceed 2 inches, or if your pavers are installed over an existing concrete slab, you will need Gator Maxx G2 instead.
Not sure whether Super Sand G2 or Maxx G2 is right for your project? Call or text us 24/7 at (856) 418-4895 and we will point you to the correct product for your joint width and base type.
Beige
Slate Grey
Is Alliance Gator Super Sand G2 the Right Polymeric Sand for Your Project?
Not compatible with overlay (concrete slab) installations. If your pavers are installed over an existing concrete slab, Super Sand G2 cannot be used. You need Gator Maxx G2 for overlay applications.
Patio pavers on a traditional gravel base The ideal choice for standard interlocking concrete paver patios with joints up to 2 inches wide on a properly prepared gravel base system.
Pool decks and pool surrounds Recommended for in-ground pool installations on a traditional base. Requires a minimum 1/8 inch per foot slope away from the pool. Pool coping joints must use mortar. Super Sand G2 is for the surrounding paver field only.
Paver driveways and parking areas Handles full vehicular and pedestrian traffic on a traditional gravel base. Sand level must be at least 1/8 inch below the paver surface or chamfer edge. All pavers must be fully interlocked. Fanned pavers do not qualify for vehicular use.
Walkways, footpaths, and commercial streetscapes Approved for a wide range of pedestrian and commercial hardscape applications including steep slopes and high-traffic areas.
Concrete pavers, natural stone, wet cast, and clay pavers Works across all standard interlocking surfaces. ASTM C144 gradation handles joints from the tightest 1/8 inch all the way to 2 inches wide.
Open-graded aggregate bases that lock or choke Can be applied when pavers are installed on aggregates that lock or choke themselves. Do not use on aggregates with large open voids, as the sand will migrate through.
What Makes Alliance Gator Super Sand G2 Different from Standard Polymeric Sand?
Second-generation intelligent polymers The same G2 formula used in the Maxx G2. These polymers chemically neutralize dust and haze during application so paver faces stay clean with no white residue after installation.
No blower required Super Sand G2 stays in the joints during application. Skip the leaf blower step entirely and save significant time and cleanup effort on every job.
Single watering to activate Alliance Gator Super Sand G2 requires just one pass with a shower-setting hose is all that is needed. No repeat watering applications required.
Rain safe in 15 minutes Alliance Gator Super Sand G2 is rain safe just 15 minutes after water activation on a traditional drainage base.
Firm yet flexible cure Once set, Super Sand G2 becomes very firm and locks securely between the paver joints while still retaining flexibility. This flexibility allows it to expand and contract with seasonal temperature changes without cracking.
ASTM C144 gradation Works in joints from the tightest 1/8 inch all the way up to 2 inches wide, making it suitable for the vast majority of standard residential paver projects.
OSHA crystalline silica compliant Meets OSHA 29 CFR 1926.1153 requirements. Safe for professional contractor use on any job site.
Waterproof bag packaging Store bags lying flat with the front facing up. Sealed intact bags can be safely stored outdoors on a pallet until needed.
Faster installation than first generation polymeric sand No blower step, a single watering, and a residue-free application all add up to significantly less time on the job.
What Gator Super Sand G2 Helps Prevent
A properly installed polymeric sand joint is your best long term defense against the most common paver maintenance problems. Here is what Super Sand G2 keeps out:
Weeds growing through paver joints Alliance Gator Super Sand G2 polymer locked joints leave no loose soil for weed seeds to take root, making weed growth through the pavers rare.
Ant tunneling and insect damage Ants cannot tunnel through a fully cured polymeric sand joint, preventing the base destabilization that causes pavers to sink and shift.
Joint erosion and washout from rain and wind Regular paver sand washes out after heavy rain. Super Sand G2's polymer bond holds the jointing material firmly in place against rain, wind, and surface runoff.
Freeze-thaw cracking Super Sand G2 remains flexible after curing, allowing it to expand and contract with seasonal temperature changes without cracking out of the joint.
Paver shifting and movement Tightly locked joints keep the entire paver surface stable under foot traffic, vehicular loads, and ground movement throughout the seasons.
White haze and dust residue on paver faces The G2 intelligent polymer formula neutralizes residue during application so paver faces stay clean without any additional cleanup step.
Note: Super Sand G2 does not prevent moss, mold, or mildew. Those result from shade, moisture retention, and drainage conditions on site. Treat with a paver-safe cleaner and improve drainage to address them.
Alliance Gator Super Sand G2 Polymeric Sand Available Colors
Super Sand G2 is available in two colors: Beige and Slate Grey. What you see on a screen looks different on your actual pavers in real outdoor light. We strongly recommend ordering physical color samples before purchasing full bags to confirm the right match for your project.
Not sure which color matches your pavers?Order our sample pack with all available colors shipped to you. Test them on your actual pavers in real outdoor light before purchasing full bags. The right color choice makes a significant difference in the finished look of your project.
How Many Bags of Alliance Gator Super Sand G2 Polymeric Sand Do You Need?
Alliance Gator Super Sand G2 polymeric sand coverage per 50 lb bag depends on your joint width. Numbers below are sourced directly from the official Alliance Gator Technical Data Sheet for standard 2-3/8 inch (6 cm) paver height. Always order 10 to 15 percent extra to account for waste and variation.
Narrow joints (1/8" to 3/8") per 50 lb bag
Beige, Slate Grey
65–85 ft²
Wide joints (3/4" to 1-1/4") per 50 lb bag
Beige, Slate Grey
22–42 ft²
Color
Narrow joints (1/8" to 3/8")
Wide joints (3/4" to 1-1/4")
Beige
65 to 85 sq ft
22 to 42 sq ft
Slate Grey
65 to 85 sq ft
22 to 42 sq ft
Minimum joint depth: 1-1/2 inches (38 mm). The entire joint depth must be filled with Alliance Gator Super Sand G2 Polymeric Sand. Coverage based on standard pavers 2-3/8 inches (6 cm) tall. Actual coverage varies by joint width, depth, and paver size. Always order 10 to 15 percent extra. Source: Alliance Gator official TDS.
How to Install Alliance Gator Super Sand G2 Polymeric Sand
Always refer to the latest Alliance Gator Super Sand G2 Technical Data Sheet (TDS) before installing. Pavers must be installed per ICPI Tech Spec No. 2. Alliance Gator Super Sand G2 is for traditional base installations only. Do not use on overlay applications.
1
Confirm everything is completely dry
The single most common installation mistake is starting on pavers that are not fully dry. Any moisture, including damp joints, will prematurely activate the polymers and cause them to stick to the paver surface, leaving white residue. Wait for a fully dry day. Pavers that have been pressure washed or rained on need at least 24 to 48 hours to dry completely. Both the paver surfaces and the joints must be bone dry before you begin.
2
Spread and sweep polymeric sand into all joints
Pour Super Sand G2 onto the dry paver surface and use a hard bristle broom to sweep it into the joints in multiple directions. Work in sections and make multiple passes to ensure full joint penetration. Leave a thin layer of sand on top of the pavers for the compaction step. Narrow joints require additional sweeping passes to fill completely.
3
Compact with a plate compactor
Run a vibratory plate compactor equipped with a rubber protective pad over the entire paved surface. Work in multiple directions to eliminate air pockets and fully pack the joints. After compacting, sweep additional sand into any joints that need topping off, then compact again. The final sand level must sit at least 1/8 inch below the top of the paver surface or 1/8 inch below the chamfer edge. The cured sand joint should never be in direct contact with foot or tire traffic.
On textured or pre-finished paver surfaces: clear all sand from the paver face before compacting to avoid scratching or damaging the surface finish.
4
Sweep off all surface excess. no leaf blower needed
Use a hard bristle broom followed by a soft broom to remove all remaining sand from the paver surfaces. With Gator Super Sand G2 you stop here. No leaf blower step is required. The G2 formula stays in the joints and does not leave residue that needs to be blown off, unlike older first generation polymeric sands.
5
Activate with water. shower setting, section by section
Set your hose nozzle to the shower setting. Start at the lowest point of the installation and work upward. Water each 30 square foot section for approximately 30 seconds until the surface repels water and it begins pooling on the joints. That pooling is the sign the polymers are activating. Move immediately to the next section. Do not over water. Standing water will wash sand out of the joints.
On slopes and pool surrounds: always start watering at the lowest point and work upward. Starting at the top will pull sand downhill and cause uneven activation.
6
Stay off until fully cured
The installation is rain safe in 15 minutes on a traditional gravel base. Keep foot traffic and vehicles off until the joints are fully cured. The joints will develop a firm crust on top after curing. This is completely normal and by design. The cured sand joint should never be in direct contact with foot or tire traffic until fully set.
Do not apply if any of these conditions exist
Paver surfaces or joints are damp or wet in any way
Temperature is at or below 32°F (0°C)
Rain is expected within 15 minutes of water activation
Pavers are installed on aggregates with large open voids, as the sand will migrate through
Pavers are installed on asphalt. Do not sweep Super Sand G2 over asphalt surfaces
Pavers are installed over an existing concrete slab. Use Gator Maxx G2 for overlay applications
Pavers are fanned rather than fully interlocked. Fanned pavers do not qualify for vehicular use
Clay pavers without first testing a small area to confirm compatibility
Long Term Maintenance for Gator Super Sand G2 Polymeric Sand Paver Joints
Alliance Gator Super Sand G2 polymeric sand is significantly lower maintenance than regular paver joint sand, but it is not completely maintenance free. Here is exactly what to do to keep your paver joints in top condition for years to come.
Routine cleaning Apply Gator Shampoo or a paver-safe cleaner to the full paver surface including the joints. Rinse with a garden hose on the shower setting at standard residential water pressure, typically up to 80 psi. No pressure washer is required or recommended directly on the joints.
White haze on pavers Usually caused by efflorescence from the pavers themselves triggered during water activation, or by polymer residue from applying on a surface that was not fully dry. Treat with Gator Efflorescence Cleaner. The haze also fades naturally over time with weathering and sun exposure.
Moss, mold, or mildew These are drainage and shade issues, not a sand problem. Treat the surface with a paver-safe cleaner. For long term prevention, improve drainage and reduce shade over the paved area.
Re-sanding worn joints Remove all old jointing material completely before re applying. Do not apply new Super Sand G2 on top of old polymeric sand. Pavers must be fully dry before starting. Then follow the standard six-step installation process from the beginning.
Storing leftover bags Super Sand G2 comes in waterproof bags. Lay bags flat with the front facing up. Sealed intact bags can be safely stored outdoors on a pallet until needed.
Technical Specifications. Alliance Gator Super Sand G2 Polymeric Sand
Minimum joint width1/8 inch (3 mm)
Maximum joint width2 inches (5 cm). traditional base only
Overlay (concrete slab) applicationsNot compatible. Use Gator Maxx G2.
Minimum joint depth1-1/2 inches (38 mm)
Minimum sand level below paver surface1/8 inch below surface or chamfer edge
Minimum install temperatureAbove 32°F (0°C)
Rain safe. traditional base15 minutes after activation
Coverage per 50 lb bag. narrow joints (1/8" to 3/8")65 to 85 sq ft per bag
Coverage per 50 lb bag. wide joints (3/4" to 1-1/4")22 to 42 sq ft per bag
Bag packagingWaterproof bag, store flat, outdoor safe
ManufacturerAlliance Designer Products Inc.
All specifications sourced from the official Alliance Gator Technical Data Sheet (TDS). Always verify the latest TDS at AllianceGator.com before installation. Specifications are subject to change by the manufacturer.
Why Buy Alliance Gator Super Sand G2 Polymeric Sand from Polymeric Sand Store?
Alliance makes excellent products. We carry them because we believe in them. Here is what you get when you order from Polymeric Sand Store that you will not find buying from Alliance directly, at a big box store, or on Amazon.
Same-day shipping on every order Order before 2 PM Eastern time and your polymeric sand ships today. Alliance does not sell direct to consumers. Home Depot and Amazon take days. We ship the same day, every day, to the continental United States.
Real expert advice available 24 hours a day, 7 days a week Call or text (856) 418-4895 any time. Tell us your joint width, paver type, and base, and we will tell you exactly which sand to order and how many bags you need.
Physical color samples before you commit We offer Beige and Slate Grey as physical 2 oz sample bags shipped directly to you. Test them on your actual pavers in real outdoor light before purchasing full bags.
Multi-brand expert selection We carry Alliance, Techniseal, Rhino, SEK, and more. We will give you an honest recommendation for your specific project, even if the right answer happens to be a different product.
Free polymeric sand calculator Enter your dimensions and joint width, and we will calculate exactly how many bags to order. No guesswork and no over buying.
30-day satisfaction guarantee If something is wrong with your order, contact us within 30 days and we will make it right. We accept returns on items that are unopened, unused, and in their original packaging. You can return the product for a full refund, or contact us for a pre-paid return label which will be deducted from your refund.
Frequently Asked Questions. Gator Super Sand G2 Polymeric Sand
Both products use the same second generation intelligent polymer technology. The key differences are joint width capacity and overlay capability. Super Sand G2 handles joints up to 2 inches wide on a traditional gravel base only and cannot be used on overlay applications over concrete slabs. Maxx G2 handles joints up to 4 inches on a traditional base and up to 2 inches on concrete slab overlays. If your joints are 2 inches or under and your pavers are on a gravel base, Super Sand G2 is the right and more economical choice. If your joints are wider or your pavers are over an existing concrete slab, you need Maxx G2. Not sure which applies to your project? Call us at (856) 418-4895.
No. Alliance Gator Super Sand G2 is not approved for overlay installations on concrete slabs. If your pavers are installed over an existing concrete slab, you must use Gator Maxx G2 instead. Maxx G2's water-repelling formula is specifically engineered to handle the moisture conditions of an overlay application. Using Super Sand G2 on an overlay can result in premature activation and joint failure.
Yes, this is completely normal and it is exactly how the product is designed to perform. The cured top layer forms a firm protective crust that spans from chamfer edge to chamfer edge. The densely compacted sand below provides the structural support. This is not a sign of installation failure.
White residue after installation is almost always efflorescence from the pavers themselves triggered by water activation, or polymer residue from applying on a surface that was not completely dry. Both respond well to Gator Efflorescence Cleaner. The haze also fades naturally over time with weather exposure. Call us at (856) 418-4895 if the problem persists after treatment.
No. This is strongly advised against by both the manufacturer and our team. The entire joint depth of at least 1-1/2 inches must be filled with Super Sand G2. If regular paver sand is used below, water and ice will penetrate from underneath and push the polymeric sand layer out over time, causing the joint to fail prematurely.
The polymers will not cure properly in freezing temperatures. This leaves the jointing sand weak and unable to lock your pavers in place. Wait until air temperatures are consistently above 32 degrees Fahrenheit, including overnight temperatures during the full curing period, before applying.
No. The intelligent G2 polymer formula does not leave residue on the paver face, so a standard broom sweep before watering is all that is needed. No blower, no extra equipment, and no additional cleanup time.
Polymeric sand is jointing sand mixed with polymer binders. When activated with water, those polymers harden the sand inside the joint, locking pavers firmly in place and resisting weeds, insects, and erosion. Regular paver sand has no binders, so it washes out after rain, allows ants to burrow freely through the joints, and requires constant replenishment. Polymeric sand is a long lasting solution when installed correctly on the right base type.
Orders placed before 2 PM Eastern time ship the same day. We keep Gator Super Sand G2 in both Beige and Slate Grey in stock at all times and ship to homeowners and contractors across the continental United States. For questions about your order, call or text us at (856) 418-4895.
You can order Gator Super Sand G2 directly from Polymeric Sand Store and have it delivered fast. Orders placed before 2 PM Eastern time ship the same day. We serve homeowners and hardscape contractors in New Jersey, Pennsylvania, New York, Delaware, Maryland, and the entire continental United States. Both colors are in stock and available to ship now.
Questions About Alliance Gator Super Sand G2 Polymeric Sand?
Call or text us 24/7 at (856) 418-4895. We will tell you exactly whether Super Sand G2 or Maxx G2 is right for your project, how many bags you need, and what to watch out for. Orders placed before 2 PM Eastern time ship the same day. Both colors are in stock.
The G2 Super Sand is easy to work with. Simply sweep, fill grout lines and sprinkle with water. Highly recommended by the contractor who installed my pavers.
